Home > Heating & Cooling > FIREPLACES & STOVES > STOVE PIPE & ACCESSORIES
Choose a sub category:
CHEMICAL CLEANERS & POLISHES HEAT PROOF CEMENTS & GASKETS INSULATED CHIMNEY PIPE
PELLET VENT PIPE STOVE PIPE - BLACK PELLET PIPE FITTINGS
STOVE PIPE FITTINGS - BLACK MISC STOVE PIPE PARTS CHIMNEY CAPS & JACKS
CHIMNEY PIPE ACCESSORIES CHIMNEY BRUSHES
Sort By:
1
Imperial GA0153 Braided Gasket Rope Imperial GA0154 Gasket Rope TAPE GASKET FBRGLS 5/8X6 WHT
Replacement gasket for airtight stoves, fireplace inserts and coal or pellet stoves. Designed to securely seal stove glass in stove doors and openings. Will withstand temperatures up to 538 Deg. C (1000 Deg. F). Replacement gasket for airtight stoves, fireplace inserts and coal or pellet stoves. Designed to securely seal stove glass in stove doors and openings. Will withstand temperatures up to 538 Deg. C (1000 Deg. F). Replacement gasket for airtight stoves, fireplace inserts and coal or pellet stoves. Designed to securely seal stove window glass in stove doors and openings. Prevents air leaks and improves efficiency. Withstands temperatures up to 1000 Deg. F (538 Deg. C).
TAPE WINDOW CHANNEL 3/4X4.5 BK Imperial BM0094 Trim Stove Pipe Collar Imperial BM0096 Trim Stove Pipe Collar
Replacement gasket for airtight stoves, fireplace inserts and coal or pellet stoves. Designed to securely seal stove window glass in stove doors and openings. Prevents air leaks and improves efficiency. Withstands temperatures up to 1000 Deg. F (538 Deg. C). Provides a finished appearance at wall or chimney opening. Install on wall where flue pipe connects to masonry chimney breech. Provides a finished appearance at wall or chimney opening. Install on wall where flue pipe connects to masonry chimney breech.
Imperial BM0052-A Stove Pipe Damper TAPE GASKET FBRGLS 3/4X6 WHT  Selkirk 208810 Storm Collar
Used to regulate air by twisting handle to open and close damper. Install in black flue pipe. Replacement gasket for airtight stoves, fireplace inserts and coal or pellet stoves. Designed to securely seal stove window glass in stove doors and openings. Prevents air leaks and improves efficiency. Withstands temperatures up to 1000 Deg. F (538 Deg. C). Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning.
ROD CHIMNEY BRUSH 48IN 1/4NPT Imperial BM0013 Adjustable Stove Pipe Elbow Selkirk 206480 Finishing Collar
Flexible, bends easily to brush hard to reach areas of the chimney. Adjustable from 0 to 90 degrees. Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee.
Imperial BM0074 Stove Pipe Reducer Selkirk 243520 Wall Bracket Imperial BM0075 Stove Pipe Reducer
Imperial Stove Pipe Reducer, Series: 611, 6 X 4 in Nominal, Small End Crimped End, 24 ga Thickness, Black For use on the exterior to support pipe to wall. Use only with Selkirk pellet stove pipe. Hold pipe 3" from wall. UL Listed. Imperial Stove Pipe Reducer, Series: 611, 6 X 5 in Nominal, Small End Crimped End, 24 ga Thickness, Black
BRUSH CHIMNEY CLEAN 8IN 1/4NPT Imperial BM0080 Stove Pipe Reducer BRUSH PELLET STOVE 4IN
Made with tough, durable black polypropylene bristles. Designed for removing soot from coal, oil, and gas stoves. Can be used in stainless steel chimneys. Imperial Stove Pipe Reducer, Series: 611, 8 X 7 in Nominal, Small End Crimped End, 24 ga Thickness, Black For pellet stove flues and clothes dryer vents. Improves heat efficiency. Reduces fire hazard. Fiber brushes work best for soot removal and heavy lint build-up in dryer vents.
Selkirk Platinum 243086 Double Wall Adjustable Length Vent Pipe Imperial GA0159 Gasket Rope BRUSH CHIMNEY CLEAN11X11 IN SQ
Type L Air Insulated Pellet Vent Adjustable Length Pipe is designed to be telescoped over a fixed length of vent in order to create an assembly of specific length. Replacement gasket for airtight stoves, fireplace inserts and coal or pellet stoves. Designed to securely seal stove glass in stove doors and openings. Will withstand temperatures up to 538 Deg. C (1000 Deg. F). Made with hundreds of stiff wire bristles. Can be used in stainless steel and clay chimneys.
Sure-Temp 266086 Double Wall Adjustable Length Smoke Pipe Pellet Pipe 243805 Horizontal Termination Stove Pipe Cap 8 in OD Selkirk 243410 Ceiling Support
Used to adjust pipe to desired length. Adjustable from 12" to 18", eliminating the need to cut pipe. Includes finishing band. For installed length, subtract 1-3/8" per joint. Horizontal Termination Cap is designed specifically for use on installations in which the Type L vent terminates in a horizontal orientation on the outside of a structure. UL Listed. Type L pellet vent ceiling support/firestop.
Selkirk 206240 Drip less Smoke Stove Pipe Adapter Sure-Temp 206435 Interior Resupport Pellet Pipe 243230B Type L Vent Stove Pipe Elbow
For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe. Allows for two different methods of chimney resupport. First method is used at the immediate section of chimney above the upper elbow of an offset. Second method is used primarily when the immediate sections of the upper offset do not pass through a joist area and resupport is necessary. Support band is clamped around the chimney immediately below a locking band.  Straps are nailed to suitable framing at two inch clearance. Type L vent systems for pellet stove applications.Used to orient pipe between vertical and horizontal orientation. Rated for flue temperatures up to 570 degrees F. Model VP may be installed with a minimum 1" air space clearance to combustible surfaces, framing lumber, drywall, and plywood. UL Listed.
Selkirk 208240 Drip less Smoke Stove Pipe Adapter Sure-Temp 206463 Insulated Wall Thimble Pellet Pipe 243100 Stove Pipe Tee With Cap
For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe. Installs quickly and eliminates need for using individual firestops. Round shielding acts as a radiation shield and provides the required 2" air space clearance to combustibles. The 2 sections telescope to accommodate 6" to 11" wall thickness. The hole opening in the faceplate for No. 206463 is 8.25"; for No. 207463 - 9.25"; and No. 208463 - 10.25". Type L Air Insulated Pellet Vent Tee with Cap designed for use in changing the orientation of the vent from horizontal to vertical and making inspection and cleaning of pellet stove system easier. UL Listed.
Sure-Temp 208400 Anchor Plate Sure-Temp 206018 Type HT Insulated Chimney Pipe Selkirk A 208825 Adjustable Roof Flashing
Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection. Type HT chimney pipe special augured in mineral wool insulation filling the space between stainless steel walls is only 1 inch thick, yet provides 17 times the insulating valve of brick. This optimum density of insulation stops expansion noises and resists and contains surges of heat. This allows the system to be enclosed with only 2 inch clearance to combustibles. The "solid pack" density comprises about 85 percent air. The mixture of extremely fine fibers trap this air in the pores of the insulation and also blocks radiation heat transfer. Tested to 2100 degrees F. UL listed. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings.
Selkirk A 206830 Adjustable Roof Flashing Sure-Temp Ultra-Temp 206410 Square Ceiling Support Sure-Temp 208018 Type HT Insulated Chimney Pipe
Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. With proper framing, all ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. Type HT chimney pipe special augured in mineral wool insulation filling the space between stainless steel walls is only 1 inch thick, yet provides 17 times the insulating valve of brick. This optimum density of insulation stops expansion noises and resists and contains surges of heat. This allows the system to be enclosed with only 2 inch clearance to combustibles. The "solid pack" density comprises about 85 percent air. The mixture of extremely fine fibers trap this air in the pores of the insulation and also blocks radiation heat transfer. Tested to 2100 degrees F. UL listed.
Imperial GA0171 Braided Gasket Rope Imperial GA0169 Braided Gasket Rope Sure-Temp 206036 Type HT Insulated Chimney Pipe
Replacement gasket for airtight stoves, fireplace inserts and coal or pellet stoves. Designed to securely seal stove glass in stove doors and openings. Prevents air leaks and improves efficiency. Withstands temperatures up to 1000 Deg. F (538 Deg. C). Replacement gasket for airtight stoves, fireplace inserts and coal or pellet stoves. Designed to securely seal stove glass in stove doors and openings. Prevents air leaks and improves efficiency. Withstands temperatures up to 1000 Deg. F (538 Deg. C). Type HT chimney pipe special augured in mineral wool insulation filling the space between stainless steel walls is only 1 inch thick, yet provides 17 times the insulating valve of brick. This optimum density of insulation stops expansion noises and resists and contains surges of heat. This allows the system to be enclosed with only 2 inch clearance to combustibles. The "solid pack" density comprises about 85 percent air. The mixture of extremely fine fibers trap this air in the pores of the insulation and also blocks radiation heat transfer. Tested to 2100 degrees F. UL listed.
Sure-Temp Ultra-Temp 208410 Square Ceiling Support Selkirk 206100 Insulated Chimney Tee with Tee Cap Sure-Temp 206148 Type HT Insulated Chimney Pipe
With proper framing, all ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a Locking Band, to pass safely through combustible walls. An Insulated Tee Cap is included which can be removed from bottom opening for inspection and cleanout. Maximum height of chimney which can be supported by an insulated Tee is 50'. Type HT chimney pipe special augured in mineral wool insulation filling the space between stainless steel walls is only 1 inch thick, yet provides 17 times the insulating valve of brick. This optimum density of insulation stops expansion noises and resists and contains surges of heat. This allows the system to be enclosed with only 2 inch clearance to combustibles. The "solid pack" density comprises about 85 percent air. The mixture of extremely fine fibers trap this air in the pores of the insulation and also blocks radiation heat transfer. Tested to 2100 degrees F. UL listed.
Sure-Temp 208009 Type HT Insulated Chimney Pipe FMI CP-8DM Chimney Pack Sure-Temp 206620 Flat Ceiling Support Kit
Type HT chimney pipe special augured in mineral wool insulation filling the space between stainless steel walls is only 1 inch thick, yet provides 17 times the insulating valve of brick. This optimum density of insulation stops expansion noises and resists and contains surges of heat. This allows the system to be enclosed with only 2 inch clearance to combustibles. The "solid pack" density comprises about 85 percent air. The mixture of extremely fine fibers trap this air in the pores of the insulation and also blocks radiation heat transfer. Tested to 2100 degrees F. UL listed. Roof flashing with 24" base, firestop spacer, round termination cap, storm collar and flue extension. Fits standard 8" inner diameter, 12-3/8" outer diameter, 1700 degree pipe. Provides the support package and termination parts for a chimney that is supported by a flat ceiling and that passes through an attic area and penetrates the roof. Just add pipe lengths and the kit has all necessary parts for complete installation. Contents: Round top, Attic insulation shield, Storm collar, Finish support package, Adjustable flashing and Smoke pipe adapter.
Selkirk 284875 High Elevation Stove Vent Kit Sure-Temp 206622 Thru-the-Wall Support Kit
For pellet and corn appliances. Kit contains: 4" horizontal cap, 4" 90-degree elbow, 4" wall bracket, (5) 4" one-foot pipe lengths, 4" tee with cleanout, 4" wall thimble, 4" tee support, 3" to 4" pellet increaser, 4" pipe connector, and 3" pipe connector. System rated for flue temperatures up to 570 degrees. Proven coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Inner wall is 304 stainless steel, outer wall is paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Meets UL-641 and UL-103. For a wall-supported chimney system with a horizontal connector passing through an exterior wall, connecting to a Tee and running vertically up the exterior wall to termination above the roof line. Provides all necessary parts for a complete installation with the exception of required insulated pipe lengths to reach your desired chimney height. Contents: Round top, 12'' Insulated pipe length, Wall band, Insulated tee/plug, Finishing collar, Wall support kit, Smoke pipe adapter and Insulated wall thimble.
   
 
1