Home > Heating & Cooling > FIREPLACES & STOVES > STOVE PIPE & ACCESSORIES > CHIMNEY PIPE ACCESSORIES
Sort By:
1
Selkirk 208810 Storm Collar Selkirk 206480 Finishing Collar Selkirk 206240 Drip less Smoke Stove Pipe Adapter
Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning. Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee. For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe.
Sure-Temp 206435 Interior Resupport Selkirk 208240 Drip less Smoke Stove Pipe Adapter Sure-Temp 206463 Insulated Wall Thimble
Allows for two different methods of chimney resupport. First method is used at the immediate section of chimney above the upper elbow of an offset. Second method is used primarily when the immediate sections of the upper offset do not pass through a joist area and resupport is necessary. Support band is clamped around the chimney immediately below a locking band.  Straps are nailed to suitable framing at two inch clearance. For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe. Installs quickly and eliminates need for using individual firestops. Round shielding acts as a radiation shield and provides the required 2" air space clearance to combustibles. The 2 sections telescope to accommodate 6" to 11" wall thickness. The hole opening in the faceplate for No. 206463 is 8.25"; for No. 207463 - 9.25"; and No. 208463 - 10.25".
Sure-Temp 208400 Anchor Plate Selkirk A 208825 Adjustable Roof Flashing Selkirk A 206830 Adjustable Roof Flashing
Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings.
Sure-Temp Ultra-Temp 206410 Square Ceiling Support Sure-Temp Ultra-Temp 208410 Square Ceiling Support Selkirk 206100 Insulated Chimney Tee with Tee Cap
With proper framing, all ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. With proper framing, all ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a Locking Band, to pass safely through combustible walls. An Insulated Tee Cap is included which can be removed from bottom opening for inspection and cleanout. Maximum height of chimney which can be supported by an insulated Tee is 50'.
FMI CP-8DM Chimney Pack Sure-Temp 206620 Flat Ceiling Support Kit Sure-Temp 206622 Thru-the-Wall Support Kit
Roof flashing with 24" base, firestop spacer, round termination cap, storm collar and flue extension. Fits standard 8" inner diameter, 12-3/8" outer diameter, 1700 degree pipe. Provides the support package and termination parts for a chimney that is supported by a flat ceiling and that passes through an attic area and penetrates the roof. Just add pipe lengths and the kit has all necessary parts for complete installation. Contents: Round top, Attic insulation shield, Storm collar, Finish support package, Adjustable flashing and Smoke pipe adapter. For a wall-supported chimney system with a horizontal connector passing through an exterior wall, connecting to a Tee and running vertically up the exterior wall to termination above the roof line. Provides all necessary parts for a complete installation with the exception of required insulated pipe lengths to reach your desired chimney height. Contents: Round top, 12'' Insulated pipe length, Wall band, Insulated tee/plug, Finishing collar, Wall support kit, Smoke pipe adapter and Insulated wall thimble.
   
 
1